Can I Repair An I Watch By Myself

Introduction

Cracked the glass on your Apple Watch? Time to go that fixed upwards. Follow this guide to replace the screen—which includes the OLED brandish and fused glass digitizer (touchscreen).

Equally a precaution against damaging your device, this guide starts by disconnecting the battery, in the only way you can—by removing information technology.

Video Overview

• Before starting repairs, take your lookout off the charger and ability it down.

• If your touchscreen is broken and prevents powering off the watch, utilize this alternating method to power it downward.



• Prepare an iOpener (or take hold of a hair dryer or heat gun) and heat the confront of the sentry until it's slightly as well hot to touch.

• Go out the iOpener on the watch for at least a minute to fully rut the screen and soften the adhesive holding information technology to the instance.

• You may need to reheat the iOpener, or move information technology around on the screen equally sections cool, to heat the screen enough to pry it off.

• Considering the gap betwixt the screen and watch body is so sparse, a sharp blade is required to separate the two. Read the following warnings advisedly earlier proceeding.

• Protect your fingers past keeping them completely articulate of the knife. If in uncertainty, protect your free hand with a heavy glove, such as a leather shop glove or gardening glove.

• Be careful not to apply too much force per unit area, every bit this might crusade the knife to sideslip and cut you, or impairment the watch.

• Wear eye protection. The knife or glass may interruption, sending pieces flying.

• Using a curved blade minimizes the chance of scratching the example or bang-up the glass. Just pry with the curved section of the bract, and not the tip or apartment section.

• Place the curved section of the blade in the gap between the drinking glass and instance on the lower edge of the watch face up, and printing firmly directly down into the gap.

• Be very careful to maintain complete control over the pocketknife—in one case the gap opens, if you're pressing too hard on the knife it may slip in and cutting the battery.

• This should wedge the gap open up and crusade the glass to lift slightly upwards from the example.

• When the glass has lifted, gently rotate the knife down, opening the gap more by pushing the glass upwardly.

• One time you've opened the gap enough, insert the tip of an opening pick under the glass.

• Slide the pick forth the bottom edge to dissever agglutinative holding the screen to the case.

• Be careful not to insert the opening selection too far. Only most one/8" ( about iii mm) is necessary, any deeper and you may impairment cables.

• Roll the opening option up the side of the push side of the watch, gently pushing in to separate the adhesive and widening the gap equally y'all go.

• Remember not to push button the pick in besides far—it's easier to avert this by rolling the pick, rather than dragging a tip along.

• Piece of work the pick around the top right corner, and scroll it forth the top edge of the screen.

• Continue working the pick around the perimeter of the screen, rolling down along the left side to cut the final of the adhesive.

• Leave the pick in place to keep the adhesive from resealing the screen in place.

• While property the first selection in place, utilize a second to check that all of the adhesive is separated around the unabridged perimeter of the screen.

• There are two cables connecting the screen to the inside of the lookout man, near the top left corner. Exist careful when prying or you may impairment these cables.

• Pry slightly up on the correct side of the screen, to free it from any remaining adhesive.

• Pry up on the left to free it as well—merely exercise non attempt to remove the screen as information technology is still held in place by two cables.

• If yous tin can run into the top layer of your Forcefulness Touch on sensor amid the display adhesive, it means the ii layers of the sensor separated and y'all're going to need to replace or repair information technology.

• iFixit screen and battery repair kits come with a replacement Force Impact sensor, so if you got one of those, don't fret.

• The top layer of the sensor may exist adhered to the back of the screen—if and so, push it back down and separate it.

• Lift the screen upward and shift information technology to the left, minding the display data and digitizer cables.

• Place the watch on an elevated surface, at least one/2" or 1 cm alpine—a small box or the edge of a volume volition work nifty. This will let the screen to hang downwards vertically and give improve admission to the bombardment.

• Be careful non to bump the screen or strain the cables while you work.

• Apply scissors to cut 1 of your opening picks to about the width of the battery. Try not to leave any sharp corners.

• Insert the modified pick between the right side of the battery and the instance.

• Utilize abiding, steady pressure to slowly pry the battery up, separating information technology from the adhesive securing it to the system board.

• Be conscientious non to deform or puncture the battery.

• On the larger (42 mm) models, it's possible to accidentally pry at the system board underneath the battery. Insert the pick simply far enough to get underneath the battery, not the system lath.

• If needed, apply a fiddling loftier concentration isopropyl alcohol (90% or greater) around and under the battery to assistance weaken the agglutinative.

• Do not attempt to remove the battery as it is nevertheless connected.

• Rotate the battery counterclockwise to betrayal its connector.

• Hold the bombardment upward and out of the way, to betrayal the battery cable connector.

• Employ a plastic opening tool, prying against the bottom of the case to separate the battery cablevision connector from the watch'due south battery cablevision.

• Remove the battery from the sentry.

• If the bombardment is visibly dented or deformed, it should be replaced. For best results, replace with a new battery whenever it is removed.

• Fold the screen up and over to the right, to expose the cables underneath.

• The brandish and digitizer cable connectors are secured below a small metallic subclass that is adhered to the speaker.

• Utilize a plastic opening tool to flip the bracket toward the brandish and upwardly from the speaker.

• If you lot just pry toward the sentinel band you may tear the cables.

• Steady the bracket from the left side using your fingers or tweezers.

• At the same time, insert a pocket-size (1 mm) flathead screwdriver under the tiny tab on the right.

• Finally, place i finger behind the tab, and pinch the bracket hard between your finger and the screwdriver to disassemble the embrace.

• This releases two slotted tabs that hold the cover to the bracket, and should gratis the encompass.

• Prying the cover off tin be challenging and may accept more than than 1 effort. Be patient, and accept care not to pull on the bracket or tear the attached cables.

• Grab the cover with your tweezers and slide it toward the top of the sentinel to costless the final slotted tab, and remove the cover.

• Carefully pry up to disconnect the brandish information and digitizer cables.

• Be careful not to touch on whatever of the exposed pins directly, as your finger oils may impede connectivity.

• Remove the display.

Team

Embed this guide

Choose a size and re-create the code beneath to embed this guide as a minor widget on your site / forum.

Preview

Source: https://www.ifixit.com/Guide/Apple+Watch+Screen+Replacement/41082

Posted by: johnsonnatitiong.blogspot.com

Share this post