How To Repair Furniture Stripped Wood Screw Holes

Download Commodity

Download Article

A stripped screw hole renders the spiral useless and tin actually be dangerous in certain situations. Luckily, there are ways that you lot can ready a stripped screw hole with the right tools. If yous have express fourth dimension and resource, y'all can practice a quick fix with toothpicks or wall plugs. If the pigsty is bigger, as would exist the instance for a lag screw or bolt, you lot may demand to use car body filler to create new threads in the hole.

1. 1

   Insert every bit many toothpicks every bit you can into the stripped spiral hole. Get regular wooden toothpicks from a section shop or online. You lot'll usually be able to fit ii or iii toothpicks into the hole.^[ane] >

   • The toothpicks should fit snugly in the hole.

2. two

   Squeeze two-3 drops of woods gum on the ends of the toothpicks. Afterward y'all employ the glue, spread the mucilage with your finger or a cotton fiber swab so that the toothpicks are completely covered in glue.^[two] You tin can buy forest mucilage online or from a hardware store.^[three]

   Advertising

3. iii

   Stick the toothpicks into the pigsty and snap off the excess. Stick the toothpicks into the hole and lightly tap on the ends with a hammer to button push them as deep as they tin tin can go into the hole. So, snap off the exposed ends of the toothpicks or interruption them off with the hammer.^[iv]

   • The toothpicks should at present run affluent with the pinnacle of the screw pigsty.

4. iv

   Allow the glue dry for at to the lowest degree 1 60 minutes. The mucilage will fuse the toothpicks to the inside of the stripped screw hole. The wooden toothpicks volition create the resistance that the spiral'south threads need to stay deeply in the hole.^[five]

   • Read the instructions on your forest glue to see if drying times differ with the brand of glue that you purchased.

5. v

   Re-insert the spiral back into the hole. Plough the spiral clockwise into the screw pigsty with a screwdriver or drill. Continue turning the spiral until the pinnacle of the screw runs flush with the hole. The new toothpicks should make full in the spaces in the screw hole and requite your screw something to grab on.^[six]

   Advert

1. ane

   Purchase plastic wall plugs online or at a hardware store. Become wall plugs that friction lucifer the size of your screw. If yous lot're unsure, utilise a tape measure or ruler to measure the length of the spiral before you purchase the plugs.^[7]

   • If y'all're buying the plugs at a hardware store, you tin bring the spiral with you lot and inquire someone for correctly sized plugs.

2. 2

   Bore a new pigsty equal to the size of the plugs if necessary. If the plugs are too big for the holes, yous'll need to bore new ones so that they tin can fit. The new holes should be i–2 centimetres (0.39–0.79 in) longer than the length of your plugs. Then, press the drill confronting the stripped hole and pull the trigger while pressing down on the drill to bore a new hole.

   • If the wall plugs fit into the existing holes, y'all don't need to drill new ones.
   • Hold a plug side by side to the tip of the drill chip and marking the length with a slice of record and so that y'all know how deep to drill.

3. iii

   Insert the plug into the pigsty. If the plug isn't fitting, tap on the top of the plug with a hammer until information applied science runs flush with the hole. The plug should fit snugly in the hole and should stay in identify.^[viii]

4. 4

   Re-insert the spiral into the plastic wall plug. Press the tip of the spiral into the plug and use a screwdriver or drill to screw it dorsum into the hole. The screw will now screw into the threads in the plug.

   Advertisement

1. i

   Bore a new pigsty into the stripped spiral hole. Utilise a drill bit that's the next size upwards from the screw. The hole must be bigger than the spiral itself and so that the automotive filler can fill the hole and bandage new threads for your spiral.^[9]

   • For case, if yous had a ¹⁄_iv inch (0.64 cm) screw, you'd diameter a hole with a ³⁄₈ inch (0.95 cm) drill bit.
   • Automotive filler is best used on larger spiral holes similar ones for bolts and lag screws.

2. two

   Mix the automotive filler co-ordinate to the directions. You can purchase automotive filler at an auto body shop or online. Read the packaging and instructions that came with the filler commencement. Then, mix the compounds together on a slice of cardboard with a putty pocketknife to activate the ingredients in the filler.^[x]

   • Almost automotive filler is made upwardly of 2 putty-like compounds that harden when mixed together.

3. iii

   Fill the pigsty with the filler. Scoop the filler upward with the putty knife and run information technology over the hole. Completely make full upwardly the hole with the filler earlier flattening out the superlative with the putty knife.^[11]

   • It may have several scoops until the hole is completely filled.

4. four

   Spray lubricant onto the finish of the screw. The lubricant will assist y'all smoothly remove the screw from the new threads ane time the automotive filler has hardened. Use a spray-on lubricant similar WD-xl to fully saturate the threads on the screw.^[12]

5. five

   Insert the spiral into the moisture putty. Practice not allow the filler dry or it will be incommunicable to insert the screw. Position the spiral in the eye of the new hole and carefully printing downwards on the top of the spiral. The spiral volition leave an banner of its threads as information technology dries.^[thirteen]

   • If the filler spills out of the sides, push button it back into the holes on the side of the spiral with your putty pocketknife.

6. 6

   Let the filler dry for five minutes and unscrew the spiral. After 5 minutes, advisedly turn the screw or bolt counterclockwise to remove it from the filler. When you lot lot expect downwards into the hole, y'all should see new threads formed by the filler.^[xiv]

   • Don't allow the filler fully gear up or y'all won't be able to remove the screw.

7. vii

   Allow the automotive filler dry overnight. The filler volition set up overnight and harden in the shape of the threads on your screw or bolt. This volition permit you to secure the screw into the new pigsty that yous created.^[15]

   Advertizing

Add New Question

• Question

  What practise y'all do when a screw pigsty is stripped?

  

  Gino Colucci is a Home Comeback Specialist and the Owner of Crackerjacks Handyman Services (not a licensed contractor) in Chandler, Arizona. Crackerjacks Handyman Services offers an effective cost-saving solution for commercial and residential repair and maintenance needs, specializing in smaller projects. Crackerjacks Handyman Services carries liability insurance and all technicians go through a groundwork bank bank check.

  

  Dwelling house Comeback Specialist

  Good Answer

  

  Back upward wikiHow past unlocking this expert answer.

  An old-school pull a fast one on is to utilise wood mucilage and toothpicks to fill the hole. Now, you can get a stiff forest epoxy or utilise threaded inserts. You can also buy repair kits to set stripped screw holes. All of these methods will piece of work well.

Ask a Question

200 characters left

Include your electronic mail address to get a message when this question is answered.

Submit

Advert

Things You lot'll Need

• Toothpicks
• Wood glue
• Hammer

• Wall plugs
• Hammer
• Drill (optional)
• Drill bit (optional)

• Drill
• Drill bit
• Automotive filler
• Putty knife
• Spray-on lubricant

About This Article

Article Summary X

To fix a stripped screw hole, get-go by inserting as many toothpicks equally y'all can into the pigsty. Once yous know how many toothpicks will fit snugly, pull the toothpicks out and squeeze 2-3 drops of woods mucilage on the ends. Then, use a cotton fiber swab to spread the glue down the length of each toothpick. Next, insert the toothpicks into the hole and tap the ends with a hammer to push button them as deep as they'll go. If the ends are nonetheless exposed, utilise your fingers or the hammer to snap off the backlog. Finally, give the woods mucilage 1 60 minutes to dry out earlier reinserting the screw back into the hole with a screwdriver or drill. For tips on fixing a larger hole with automotive filler, read on!

Did this summary aid you?

Thanks to all authors for creating a page that has been read 357,140 times.

Did this commodity assistance you?

Source: https://smithwhearclas.blogspot.com/2022/03/how-to-fix-stripped-cabinet-screw-holes.html

Posted by: johnsonnatitiong.blogspot.com

Share this post